Ke970 users manual

Enter text from picture: To support Remote power on function for factory mass production, applied an analog switch as following figure. Keypad Back Light Trouble 5. Control Signal is OK.

This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.

We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website.

These cookies do not store any personal information. Skip to content. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Replace the Q is damaged working? This is to avoid that the download is stopped accidentally. Introduction A local telephone company may make changes in its communications facilities or procedure.

SD mode Pin No. It has been specially designed for usage with S-Gold2. Front End Module control Implemented in the Transceiver are two outputs for direct control of front end modules with two logic input pins to select RX- and TX-mode as well as low- and high band operation. Furthermore, to avoid that the download is stopped on a mouse double-click, there must be at least 0.

Figure 19 Audio signal flow diagram — 46 A local telephone company may make changes in its communications facilities or procedure. RF Calibration steps as follow:. This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.

We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Lower quality blades often have inferior cutting capacity and a shorter service life, which results in a higher cost in relation to the quantity of material that is cut. See the instructions under the heading Assembling the cutting blade.

Only specialty blades. Never use a cutting blade with a lower speed rating than that of the power cutter. Otherwise replace the blade. If the blade does not produce a resonant, ringing sound it is damaged. A cutting blade may burst and cause injury to the operator. Never use a cutting blade for any other purpose than that it was intended for. Cutting plastics with a diamond blade can cause kickback when the material melts due to the heat produced when cutting and sticks to the blade.

Never cut plastic materials with a diamond blade! Never use a cutting blade at a lower speed rating than that of the power cutter. Only use cutting blades intended for high speed handheld power cutters.

Add page 9 to Favourites. Ask your dealer for help in choosing the right product. Working with a blunt diamond blade causes overheating, which can result in the diamond segments coming loose.

If this is not done, the blade may be overheated. All blades should be removed from the cutter after use and stored carefully. Special care should be taken with abrasive blades. If an abrasive blades is stored in humid conditions, this can cause imbalance and result in injury. Blade typeMaterial Concrete blade Concrete, asphalt, stone masonry, cast iron, aluminium, copper, brass, cables, rubber, plastic, etc. Metal bladeSteel, steel alloys and other hard metals.

Do not use abrasive blades with water. The strength is impaired when abrasive blades are exposed to water or moisture, which results in an increased risk of the blade breaking. Diamond blades get very hot when used. An overheated blade is a result of improper use, and may cause deformation of the blade, resulting in damage and injuries.! Never use toothed blades such as wood cutting blades, circular toothed blades, carbide tipped blades etc.

Carelessness can result in serious personal injury or even death. Government regulation requires a different type of guarding for carbide tipped blades not available on power cutters — a so called degree guard. Power Cutters this saw use Abrasive or Diamond blades and have a different guarding system which does not provide protection against the dangers presented by wood cutting blades.

Add page 10 to Favourites. Use a bushing with the correct diameter! The blades are marked with the diameter of the centre hole. Spatter and sparks from the material being cut are then collected up by the guard and led away from the user.